Cooling checks go in the spring. Heating checks go in the fall. Book both before the season starts, and get the customer looking at their filter once a month in between. That is the whole schedule for most homes, and it is what ENERGY STAR tells homeowners to expect from their contractor.
The hard part is running it across a few hundred addresses without losing anyone. Here's how I'd set it up.
A planning guide, not a manufacturer requirement. The equipment manufacturer's instructions and any service agreement you have with the customer come first.
Why the season picks the date
Two reasons, and only one of them is about the customer.
The first is the equipment. ANSI/ACCA 4 QM, the ACCA standard for maintaining residential HVAC systems, says cooling and heating inspection tasks should be done while the equipment is running inside the temperature range the manufacturer allows. So a cooling check on a cold morning in March can't tell you much. Wait until it's warm enough to run the A/C properly. Then get there before the first hot week.
The second is your own calendar. ENERGY STAR's maintenance checklist points out that contractors get busy once summer and winter arrive, which is why it tells homeowners to book cooling in spring and heating in fall. It even suggests tying the check-ups to the clock changes so people remember. That's a handy line to put on a reminder card.
Sort the list by what's at the address
Don't give every customer the same plan. ACCA 4's task tables mark some items semiannual and others annual, including most of the gas combustion and venting checks. It also lets the contractor recommend dropping from two visits a year to one for heating-only or cooling-only equipment that runs in just one season.
| Equipment at the address | Visits a year | When | Sheet to print |
|---|---|---|---|
| Gas furnace and central A/C | 2 | Spring for cooling, fall for heating | AC checklist in spring, furnace checklist in fall |
| Heat pump | 2 | Spring and fall | HVAC checklist (it has the reversing valve and defrost line) |
| Heating-only furnace | 1 (your call) | Fall | Furnace checklist |
| Cooling-only A/C | 1 (your call) | Spring | AC checklist |
A heat pump runs in both seasons, so it doesn't fit the heat-only or cool-only exception. Keep it on two visits.
The one-visit rows are a recommendation you make, not a rule. ACCA 4 also goes the other way: if successive visits keep finding problems, you can recommend more frequent visits. Either way, the homeowner decides whether to take it.
Set the next date before you leave
The cheapest booking you'll ever make is the one you make standing in the customer's basement. Our general service checklist ends with a "Next service date agreed" line for exactly this reason. Write the date on the sheet, then put it in your calendar before you start the truck.
On a two-visit customer, the fall visit books the spring one, and the spring visit books the fall one. Miss one handoff and that customer drops off the schedule until they call you with no heat.
Filters are the customer's job, so show them
ENERGY STAR tells homeowners to check the filter once a month and clean or change it as needed, and adds that the contractor can show them how. So show them. It takes a minute while you're already at the air handler.
Write the filter size in the blank on the sheet (the HVAC, furnace and AC templates all have one). Next time the customer calls asking what size to buy, the answer is in the job folder.
Keep last visit's sheet in the folder
A schedule only earns its keep if each visit can be compared with the one before. Write the readings in the Notes column: amps, temperature rise, temperature split, CO, gas pressure. A capacitor reading that dropped since spring, or a temperature rise creeping toward the top of the nameplate range, is the evidence you need when you recommend an extra visit or a repair.
Paper works fine for this up to a point. One folder per address, newest sheet on top.
When the list outgrows a wall calendar
Once the list is too long to keep in your head, a paper calendar starts dropping people. That's when scheduling software starts to make sense.
Plan features change, so check Jobber's own pricing page for what each tier includes before you pick one.
For what each of those visits should cover line by line, see our HVAC tune-up checklist.
Whatever you schedule with, print the right sheet for the season: the AC checklist for spring visits, the furnace checklist for fall, or the combined HVAC checklist for heat pumps and one-trip jobs.