HVAC Maintenance Checklist
A ready-to-print HVAC service checklist with furnace and AC sections. Add your logo, edit the items, print or save as PDF.
How to use| Item | OK | Needs attention | N/A | Notes |
|---|---|---|---|---|
| General / controls | ||||
| Thermostat operation, settings and batteries | ||||
| Air filter checked / replaced (size: ) | ||||
| Electrical connections tight, no signs of overheating | ||||
| Motor voltage and amperage within nameplate rating | ||||
| Moving parts lubricated where required | ||||
| Condensate drain, trap and pan cleaned and flowing | ||||
| Float / condensate safety switch tested | ||||
| System starts, runs and shuts off properly | ||||
| Furnace / heating | ||||
| Burners clean, flame even and blue | ||||
| Heat exchanger inspected for cracks or corrosion | ||||
| Igniter and flame sensor checked / cleaned | ||||
| Gas pressure checked, no leaks at gas connections | ||||
| Flue and venting secure, proper draft | ||||
| Carbon monoxide test (record ppm) | ||||
| High-limit and safety switches tested | ||||
| Blower wheel, motor and belt inspected | ||||
| Temperature rise within manufacturer range | ||||
| Air conditioning / cooling | ||||
| Condenser coil cleaned, area clear of debris | ||||
| Evaporator coil inspected / cleaned | ||||
| Refrigerant pressures, superheat / subcooling recorded | ||||
| Capacitor tested (rated / actual µF) | ||||
| Contactor inspected for pitting or burning | ||||
| Condenser fan motor and blade checked | ||||
| Heat pump: reversing valve and defrost checked | ||||
| Refrigerant line insulation intact | ||||
| Supply / return temperature split recorded | ||||
| Airflow | ||||
| Visible ductwork sealed, no disconnections | ||||
| Supply registers and return grilles open and clear | ||||
| Total external static pressure recorded | ||||
How to use
- The HVAC template is already loaded, with general, furnace, AC and airflow sections. To mix in other trades, use the custom builder.
- Add your business name, logo and the job details, or leave them blank to fill in by hand.
- Edit, add, remove or move items and sections. The preview updates as you type.
- Press Print, or Save as PDF and choose “Save as PDF” in the print window.
- Save a draft to reuse the same checklist on your next job.
About this HVAC maintenance checklist
Use it as an HVAC preventive maintenance checklist, a seasonal tune-up sheet or a furnace and AC service checklist. Readings such as CO, refrigerant pressures, capacitor values and temperature split go in the Notes column. For hot water and steam boilers, use the boiler maintenance checklist. For a single system, use the furnace maintenance checklist or the AC maintenance checklist. For a heat pump, keep the cooling section and the reversing valve and defrost line; our heat pump maintenance checklist lists the owner jobs and the service visit items to add.
HVAC maintenance by frequency
The printed sheet is grouped by part of the system so it follows the way you work round a unit. Here is the same work grouped by how often it usually comes up. Intervals vary with the equipment, the filter, the building and the service agreement, so follow the manufacturer first.
| Check | Why it matters |
|---|---|
| Check or replace the air filter | A clogged filter cuts airflow, which can freeze an evaporator coil in cooling and trip the high limit in heating. |
| Check the thermostat is calling and the system responds | Catches dead batteries, wrong settings or a lost schedule before the customer calls it a breakdown. |
| Look at the condensate drain and pan | A blocked drain is one of the most common causes of water damage and float-switch shutdowns. |
| Check | Why it matters |
|---|---|
| Clean the condenser coil and clear the area round it | A dirty condenser raises head pressure, amps and running cost, and shortens compressor life. |
| Record pressures, superheat and subcooling | Readings on file show a slow leak or a metering problem over time, instead of guessing on the day. |
| Test the run capacitor against its rating | A weak capacitor makes motors run hot and is a common no-cool call in the first heat wave. |
| Check the contactor for pitting | Burnt contacts drop voltage to the compressor and can weld closed. |
| Record the supply and return temperature split | A quick sign of low charge, low airflow or a dirty coil. |
| Check line set insulation | Missing suction line insulation costs capacity and drips water inside. |
| Check | Why it matters |
|---|---|
| Inspect the heat exchanger | Cracks can let combustion gases into the supply air. |
| Clean the flame sensor and check the igniter | A dirty sensor is a common cause of lockouts on modern furnaces. |
| Test for carbon monoxide and check venting and draft | CO is the safety risk on any fuel-burning appliance. Record the reading. |
| Check gas pressure and connections for leaks | Wrong manifold pressure affects combustion and heat exchanger life. |
| Test the high limit and safety switches | They are what shuts the burner down when airflow fails. |
| Check temperature rise against the nameplate range | Too high means low airflow; too low can mean condensing in the heat exchanger. |
| Check | Why it matters |
|---|---|
| Measure total external static pressure | Shows duct restrictions and blower problems that a filter change will not fix. |
| Tighten electrical connections and check motor amps | Loose terminals overheat; high amps warn of a failing motor or bearing. |
| Inspect visible ductwork for disconnects | A loose return in an attic or crawlspace pulls in hot, dusty air. |
If HVAC is one part of a wider building plan, our preventive maintenance schedule template shows how to keep every task and its next due date in one list.
Printing it
Print one sheet per unit. It fits on one Letter or A4 page in plain black and white, with write-in blanks for readings. Leave it blank for the truck, or fill in your business details and the customer first and save it as a PDF to email after the visit. For a line-by-line look at what each seasonal visit should cover, see our HVAC tune-up checklist guide.
Readings worth recording
In cooling: suction and liquid pressures, superheat, subcooling, the temperature split, capacitor values and compressor amps. In heating: CO, gas pressure and temperature rise. Write them in the Notes column so the next visit has something to compare against.
Questions
What does an HVAC maintenance checklist cover?
This one covers controls and filters, furnace checks (burners, heat exchanger, flame sensor, venting, CO test, safety switches), AC checks (coils, refrigerant readings, capacitor, contactor, temperature split) and airflow. Remove anything that does not apply to the unit.
Can I use it for a furnace-only or AC-only visit?
Yes. Remove the section you do not need with its ✕ button, or change the title to Furnace Maintenance Checklist or AC Maintenance Checklist.
How often should HVAC equipment be serviced?
Most manufacturers recommend a heating tune-up before winter and a cooling tune-up before summer. Follow the equipment manufacturer and any service agreement you have with the customer.